硬质泡沫塑料吸水率测定仪产品简介：
硬质泡沫塑料吸水率测定仪是根据国家标准GB8810-2005《硬质泡沫塑料吸水率检测》设计制造。具有使用简单、度高的特点，可被广泛使用于制造、科技的硬质泡沫塑料吸水率测试。
First, the product introduction:
It is designed and manufactured according to the national standard GB8810-2005 "hard foam plastic water absorption rate detection". It has the characteristics of simple use and high precision, and can be widely used in the manufacturing and technology of rigid foam water absorption test.
二，系统组成： 
鑫生卓锐北京公司公司硬质泡沫塑料吸水率测试系统是由：硬质泡沫塑料吸水率测试计算软件、试样装载网笼、测试样品水箱、硬质泡沫塑料质量测量仪、试样切片器、玻璃载片等六大部分组成。
Second, the system consists of
The rigid foam plastic water absorption test system is composed of: rigid foam plastic water absorption rate test calculation software, sample loading special net cage, test sample water tank, rigid foam plastic quality measuring instrument, sample special slicer, glass slide, etc. The six major components.

三，技术参数：
★称量范围：5000g   测量精度：0.1g
★溢流箱规格：φ200*215mm
★网笼尺寸：Φ200*250mm 
★电压：200V
★外形尺寸：1000*600*800mm
★切片厚度0.1-0.4mm可调
★泡孔φ测试仪：*小计算孔径：0.1mm
Third, technical parameters
★Weighing range: 5000g Measurement accuracy: 0.01g
★Overflow box specification: φ200*215mm
★ Net cage size: Φ200*250mm
★Voltage: 200V
★Dimensions: 1000*600*800mm
★ slice thickness 0.1-0.4mm adjustable
★ Cell φ tester: * Small calculation aperture: 0.1mm

四，使用方法：
★被测物尺寸：长度 150MM、宽度150mm、厚度 75mm；休积不大于500cm3；
★环境温度：23±2℃      环境湿度：50±5﹪
★泡水液：蒸馏后至少放置 48小时的蒸馏水；
★将硬质泡沫切割成长 150MM宽 150毫米厚 75mm的正方形被测物。
★将试样放于天平上，（北京鑫生卓锐科技有限公司供应硬质泡沫塑料吸水率测定仪*）称量干燥后的试样重量（m1），准确至 0.1g，并记录。
★悬挂网笼浸入蒸馏水中，除去悬挂网笼表层气泡，挂于天平的下称钩上，称其表现重量（m2），准确至 0.1g，并记录下来，记住后将悬挂网笼取下。
★将悬挂网笼2边套筒上的2个固定螺钉分别拧松，再将试样安放圆盘上并居中；将压棒下调压住试样，压棒2端紧扣试样，并旋紧2边套筒上的两个固定螺钉。
★将安装好试样的悬挂网笼重新浸入蒸馏水中，用软毛刷跟搅拌除去悬挂网笼和硬质泡沫表层气泡。
★浸泡96小时后，将盛有试样的悬挂网笼挂于天平下称钩上，称量其表现质量（m3），准确至0.1g，并记住下来 。
Fourth, the method of use
★Measurement object size: length 150MM, width 150mm, thickness 75mm; rest is not more than 500cm3;
★ Ambient temperature: 23±2°C Ambient humidity: 50±5%
★ soaking liquid: at least 48 hours of distilled water after distillation;
★ Cut the rigid foam into 150mm wide 150mm thick 75mm square measured object.
★ Place the sample on the balance and weigh the dried sample (m1) to the nearest 0.1g and record.
★The hanging net cage is immersed in distilled water to remove the air bubbles on the surface of the hanging net cage. It is hung on the lower hook of the balance, and its performance weight (m2) is called, accurate to 0.1g, and recorded, remember to take off the hanging net cage. .
★ Loosen the two fixing screws on the sleeve of the hanging cage 2, and place the sample on the disc and center it; press the pressure rod down to press the sample, press the end of the pressure rod 2, and rotate Tightening the two setscrews on the two side sleeves.
★ Re-dip the hanging net cage with the sample installed into the distilled water, and use a soft brush to stir and remove the hanging net cage and the foam bubbles on the surface of the rigid foam.
★ After soaking for 96 hours, hang the hanging net cage containing the sample on the hook under the balance, weigh the performance quality (m3), accurate to 0.1g, and remember it.

鑫生卓锐北京有限公司